Categorias de produtos:
Atlas Copco ZT 30 VSD (FF VSD⁺) Oil-free Tooth Air Compressor
$15,000.00
The Atlas Copco ZT 30 VSD is the 30 kW air-cooled oil-free tooth compressor offered with a standard variable-speed tier at 8.6 bar(e) and a VSD⁺ tier that adds a 10 bar(e) class at 66 dB(A). Tell us the working pressure your loop needs and whether the dryer should sit inside the canopy, and we will confirm the exact tier before we prepare the Atlas Copco ZT 30 VSD quotation.
The Atlas Copco ZT 30 VSD is the 30 kW air-cooled rung of the oil-free tooth range, and it is documented across two variable-speed tiers that behave quite differently. The lower tier, printed as the ZT30VSD, carries a single 8.6 bar(e) class, 76 dB(A) and a 1400 kg pack restricted to the IMD dryer.
The upper tier, the ZT30VSD+, keeps the same 30 kW motor but spreads over 8.6 and 10 bar(e) classes, drops the rated noise to 66 dB(A) and opens the dryer choice to both ID and IMD builds at 1350 kg. That 10 dB(A) gap between the two tiers is the widest step-to-step change in the whole 15-55 VSD catalogue, which makes the ZT 30 VSD the frame where the upgrade decision changes the acoustic character of the room, not just the pressure ceiling.

The ZT30VSD Tier — One 8.6 bar(e) Class
The standard variable-speed tier is measured across three rows, all within one pressure class. At Minimum the machine starts at 4 bar(e) and moves 42.4–81.1 l/s, at the Effective point of 7 bar(e) it reads 41.3–79.8 l/s, and the Maximum row at 8.6 bar(e) closes at 41.2–76.1 l/s. The m³/min column tracks the same shape, running 2.5–4.9 at Minimum and easing to 2.5–4.6 at Maximum. Motor power is listed once at 30 kW, the noise level is printed at 76 dB(A), and the standard model weight is 1400 kg. The dryer column shows only IMD, so this tier cannot be ordered with the lighter ID build — a restriction the VSD⁺ tier below does not share.
| Pressure class | Point | Pressão de serviço (bar(e)) | FAD (l/s) | FAD (m³/min) | Ruído em dB(A) |
|---|---|---|---|---|---|
| 8.6 bar(e) | Mínimo | 4 | 42.4–81.1 | 2.5–4.9 | 76 |
| 8.6 bar(e) | Eficaz | 7 | 41.3–79.8 | 2.5–4.8 | 76 |
| 8.6 bar(e) | Máximo | 8.6 | 41.2–76.1 | 2.5–4.6 | 76 |
The ZT30VSD+ Tier — Two Pressure Classes
The VSD⁺ tier belongs to the ZR/ZT 30-50 VSD⁺ family and its catalogue rows split into two pressure classes. Within the family the drive combines a permanent-magnet motor with the tooth compression element, and the printed output starts at 40.4–95.5 l/s on both classes at Minimum. The 8.6 bar(e) class holds 39.9–93.6 l/s at its effective point and closes at 37.9–74.8 l/s, while the 10 bar(e) class trades top-end flow for pressure and finishes at 36.9–64.8 l/s. Both classes are rated at 66 dB(A), and the pack weight of 1350 kg covers the whole tier rather than one class.

8.6 bar(e) Class of the ZT30VSD+
| Point | Pressão de serviço (bar(e)) | FAD (l/s) | FAD (m³/min) | Ruído em dB(A) | psig column |
|---|---|---|---|---|---|
| Mínimo | 4 | 40.4–95.5 | 2.4–5.7 | 66 | 58 |
| Eficaz | 7 | 39.9–93.6 | 2.4–5.6 | 66 | 102 |
| Máximo | 8.6 | 37.9–74.8 | 2.3–4.5 | 66 | 125 |

10 bar(e) Class of the ZT30VSD+
| Point | Pressão de serviço (bar(e)) | FAD (l/s) | FAD (m³/min) | Ruído em dB(A) | psig column |
|---|---|---|---|---|---|
| Mínimo | 4 | 40.4–95.5 | 2.4–5.7 | 66 | 58 |
| Eficaz | 9 | 37.7–71.7 | 2.3–4.3 | 66 | 130 |
| Máximo | 10 | 36.9–64.8 | 2.2–3.9 | 66 | 145 |

Weights, Dimensions and Dryer Builds of the ZT 30 VSD
The two tiers also differ in how they occupy a floor and which dryer builds they accept. The standard ZT30VSD sits in the ZT 30-55 VSD dimension group at 2440 × 1016 × 1880 mm and weighs 1400 kg with its IMD-only dryer restriction. The ZT30VSD+ instead belongs to the VSD⁺ family dimensions of 2005 × 1022 × 1909 mm, stretching to 2440 mm in length once the Full Feature build is ordered.
Its weight table is shared across the 30 and 37 kW frames of the family: 1350 kg packed, 1610 kg as Full Feature with the iMD dryer and 1504 kg as Full Feature with the iD dryer. The dryer column on the VSD⁺ tier reads ID / IMD, so buyers who previously had to accept IMD now get the lighter integrated option as well.
| Tier | Pack weight | Full Feature (iMD) | Full Feature (iD) | Dimensions (mm) | Full Feature length | Dryer builds |
|---|---|---|---|---|---|---|
| ZT30VSD | 1400 kg | — | — | 2440 × 1016 × 1880 | — | IMD |
| ZT30VSD+ | 1350 kg | 1610 kg | 1504 kg | 2005 × 1022 × 1909 | 2440 mm | ID / IMD |
Motor Ratings Behind the ZT 30 VSD
Motor documentation for the 30 kW frame comes from two official prints. The VSD⁺ specification tables rate the drive at 40 hp in the imperial column, and the North American CAGI data sheet for the ZT 30 FLX VSD, dated 03-18-2025, lists a Drive Motor Nominal Rating of 40.2 & 40.2 hp at 96.3 percent efficiency, with a 1.3 hp fan motor at 54.0 percent. The same sheet records a full load operating pressure of 124.7 psig on the 8.6 bar(e) build and 145.0 psig on the 10 bar(e) build.
The measured field behind those ratings is equally relevant. Input power spans 35.5 kW down to 19.5 kW across the turndown range, and specific power sits between 22.8 and 25.9 kW per 100 acfm on the 8.6 bar(e) build. These figures matter to buyers who must justify installed electrical load, because they show the 30 kW frame drawing barely half its nominal rating at the bottom of its speed band.
Where the ZT 30 VSD Fits in a Plant
Air-cooled duty at 30 kW usually means one compressor room corner serving a mixed load: instrumentation air at moderate pressure plus an occasional higher-pressure loop. The standard tier of the ZT 30 VSD covers the first case cleanly, holding 79.8 l/s at 7 bar(e) with the IMD dryer handling dew point inside the canopy. The VSD⁺ tier suits plants where the same machine must also feed a 10 bar(e) consumer, since its 10 bar(e) class still moves 71.7 l/s at the effective point while running at 66 dB(A).
Plants that measure noise against adjacent workstations gain the most, because the 10 dB(A) drop between tiers is perceived as roughly a halving of loudness. Maintenance planning is simpler too: at 1350 kg packed and a 2005 mm footprint, the VSD⁺ build passes standard doorways that stop longer frames, and the shared weight table means a future 37 kW upgrade reuses the same pad.
Questions Buyers Ask About the ZT 30 VSD
How much quieter is the VSD⁺ tier than the standard tier? The standard ZT30VSD is printed at 76 dB(A) and the ZT30VSD+ at 66 dB(A), a 10 dB(A) step that is the widest between adjacent tiers in the catalogue. Both figures are measured noise levels for the complete packaged machine, so no additional enclosure allowance is needed when comparing the two.
Why does the standard tier offer only the IMD dryer? The catalogue row for ZT30VSD-8.6 lists IMD alone in the integrated dryer column, while the ZT30VSD+ rows list ID / IMD. The ID build saves 106 kg against the iMD Full Feature weight, which matters where the machine sits on an elevated slab or mezzanine.
What does the CAGI sheet add for North American buyers? It confirms the 40.2 & 40.2 hp drive motor at 96.3 percent efficiency and gives measured specific power from 22.8 to 25.9 kW per 100 acfm on the 8.6 bar(e) build, letting engineers compare the ZT 30 VSD directly against any CAGI-listed competitor at the same test conditions rather than relying on nameplate data alone.
From the ZT 30 VSD to the ZT 37 VSD
Stepping up one frame changes the tier structure rather than merely the flow numbers. The ZT 37 VSD keeps the single 8.6 bar(e) class on its standard tier but adds a second 10 bar(e) gear there, and its VSD⁺ tier lifts the minimum flow floor to 112.6 l/s at 4 bar(e). Buyers whose demand profile sits between 80 and 100 l/s therefore face a genuine choice: stay on the ZT 30 VSD and accept the 8.6 bar(e) ceiling on the standard build, or move to the 37 kW frame for the two-gear standard tier. Either way, sending us the target pressure and flow band lets us match the tier to the load before quotation.
| Peso | 1350 kg |
|---|---|
| Dimensões | 200.5 × 102.2 × 190.9 cm |
| Pressão máxima de funcionamento em bar(e) | 10 |
| Pressão máxima de funcionamento em psig | 145 |
| Motor instalado | 30 kW |
| Potência do motor instalada | 40 hp |
| Capacidade FAD l/s | 41.2 – 95.5 |
| Capacidade FAD m³/min | 2.3 – 5.7 |
| Nível de ruído | 66 dB(A) |
| Dimensões (C × L × A) | 2005 × 1022 × 1909 mm |
| País de origem | CN |
| Código SH | 8414804990 |
| Prazo de execução | 2-4 semanas |
| MOQ | 1 unidade |
| Embalagem | Caixa de madeira |
| Qualidade do produto | 100% Genuíno, 100% Original, Novo |
| Modo de transação | CFR, CIF, CIP, CPT, DAP, DDP, EXW, FCA |



































Wojciech S -
Our bottleneck was a 30 kW oil-free frame that could still hold 7 bar(e) through wide flow swings, and the Atlas Copco ZT 30 VSD answered it. The VSD⁺ build idles around 66 dB(A), so the compressor corner of the workshop finally lost its ear-protection sign. At the effective point it still moves 93.6 l/s, which covers our two packaging lines with margin. Ordering was straightforward once we sent the pressure class and dryer preference.