فئات المنتجات:
3002600350: ATLAS COPCO MOTOR NON DRIVE SIDE KIT
$680.00
The Atlas Copco 3002600350 motor non-drive-side kit is the bearing-and-seal set listed for oil-injected screw compressors in the GA 55, GA 75 and GA 90 parts catalogues. It contains one ball bearing, one external circlip, one DIN471-75X2.5 circlip and one seal lip, supplied as a 1.3 kg set measuring 205 x 205 x 125 mm. Send us the number from your old kit plus your compressor model and serial number, and our parts desk will confirm the match before we quote.
The Atlas Copco 3002600350 is the motor non-drive-side kit for oil-injected screw compressors. It is a small repair set rather than a complete motor: the 3002600350 restores the bearing support and the sealing at the end of the motor opposite the drive coupling. The kit appears in the motor repair sections of the fixed-speed GA 55 / GA 75 catalogue and the GA 55+ / GA 75+ / GA 90 catalogue, and it is also listed for the GA 55 VSD, GA 75 VSD and GA 90 VSD machines. One number covers all of them. The recorded set weighs 1.3 kg and measures 205 x 205 x 125 mm.
What Arrives Inside the 3002600350 Non-Drive-Side Kit
The 3002600350 is defined by its four-line bill of materials, and each piece has a distinct job at the non-drive end. The ball bearing, quantity one, carries the rotor weight and locates the shaft at the end away from the coupling. The external circlip, quantity one, seats in the shaft groove and holds the bearing inner race against axial movement. The second retaining ring is listed specifically as CIRCLIP-DIN471-75X2.5, quantity one, a 75 mm shaft ring with a 2.5 mm section that differs from the external circlip and is not interchangeable with it. The seal lip, quantity one, closes the housing against grease loss and contamination at the same end.
Because the kit mixes two different circlips, an outer clip and a DIN471-75X2.5 internal ring, the 3002600350 is not a generic bearing pack. Buyers replacing a single ring from a mixed box can end up with the wrong clip seated in the wrong groove. The set is recorded at 1.3 kg on a 205 x 205 x 125 mm envelope, a flat, square footprint that reflects the small parts count rather than a full motor assembly.

One Non-Drive-Side Number Across Two Rebearing Families
The most useful fact about 3002600350 is what does not change. In the GA 55 and GA 75 fixed-speed group, the motor repair set is 3002600330, the drive-side kit is 3002600340, the non-drive-side kit is 3002600350, and the fan kit is 1092026400. In the GA 55+, GA 75+ and GA 90 group, the rebearing kit changes to 3002600360 and the drive-side kit changes to 3002600370, yet the non-drive-side kit stays 3002600350 and the fan kit stays 1092026400. The bearing and drive ends split into two part-number families; the non-drive end does not.
The VSD catalogue repeats the same pattern. For the GA 55 VSD machine the listed set is 3002600330 with drive side 3002600340 and non-drive side 3002600350. For the GA 75 VSD and GA 90 VSD machines the rebearing kit is 3002600360 with drive side 3002600370, and the non-drive side is once again 3002600350. Whether the motor belongs to the older fixed-speed range or the VSD range, the part you need at the non-drive end carries the same number. A working example of the platform this kit serves is the Atlas Copco GA 90 (FF 90⁺) oil-injected air compressor.
This is why identifying the end of the motor matters more than identifying the machine when you order 3002600350. The same kit can serve a GA 55, a GA 75+, a GA 55 VSD or a GA 90 VSD, provided the work is at the non-drive side. The catalogue groups the other three kits by motor family, but it deliberately leaves the non-drive-side kit shared.

Specification Summary
| البند | Record |
|---|---|
| اسم الجزء | MOTOR NON DRIVE SIDE KIT FOR OIL INJECTED SCREW COMPRESSORS |
| رقم الجزء | 3002600350 |
| Kit Contents | BALL BEARING x1; EXT.CIRCLIP x1; CIRCLIP-DIN471-75X2.5 x1; SEAL LIP x1 |
| السعر | 680.00 EUR |
| المنشأ | كن |
| رمز التعريفة | 8414909090 |
| الأبعاد (الطول × العرض × الارتفاع) | 205 x 205 x 125 mm |
| الوزن | 1.3 kg |
| Side | Non-drive end of the motor |
| التطبيق | GA 55, GA 75, GA 55+, GA 75+, GA 90 fixed speed; GA 55 VSD, GA 75 VSD, GA 90 VSD |

Non-Drive Side or Drive Side: Choosing the Correct Kit
The four kit numbers in each motor family sit next to each other in the catalogue, which is exactly how the wrong one gets ordered. The rebearing kit, 3002600330 or 3002600360, is the broad set for a full re-bearing of the motor. The drive-side kit, 3002600340 or 3002600370, serves the coupling end where the load is transmitted. The 3002600350 is confined to the opposite, non-drive end. The fan kit 1092026400 is a separate item again and is shared across both families just like the 3002600350.
Confirm the end of the motor before you confirm the machine model. A noisy non-drive end with a worn bearing and a weeping seal points to 3002600350, while play at the coupling end points to a drive-side kit. If both ends need attention, the catalogue lists the rebearing kit as the combined option rather than two separate orders. Reading the old part off the removed ring or bearing, together with the machine serial number, removes the guesswork between four similar kit numbers.

Fitting Checks on the Non-Drive End
Start by comparing the removed parts against the four lines in the 3002600350: one ball bearing, the external circlip, the DIN471-75X2.5 ring and the seal lip. The DIN471 ring is sized to a 75 mm shaft with a 2.5 mm section, so measure the groove in the old shaft before assuming a clip from another kit will seat correctly. Clean the bearing housing and the shaft groove, then check that the new circlip sits fully in its groove and that the seal lip faces the direction the old seal faced.
Press on the bearing inner race rather than the outer race, and stop as soon as the bearing seats against its shoulder, so the seal lip is not damaged during fitting. After assembly, turn the shaft by hand to confirm it runs free before the motor is re-coupled. The 3002600350 covers the non-drive side only, so a bearing that failed from coupling misalignment should be investigated at the drive end as well; otherwise the new parts may not last.
الأسئلة المتداولة
Is 3002600350 the same part on a GA 55, a GA 75+ and a GA 90 VSD? Yes. The catalogues list 3002600350 as the non-drive-side kit for the GA 55 and GA 75 fixed-speed group, the GA 55+, GA 75+ and GA 90 group, and the GA 55 VSD, GA 75 VSD and GA 90 VSD machines. The rebearing and drive-side numbers change between groups; the non-drive-side number does not.
What exactly is inside the 3002600350 kit? Four pieces, one of each: a ball bearing, an external circlip, a circlip listed as DIN471-75X2.5, and a seal lip. The two circlips are different parts and are not substitutes for each other.
Which number do I need for the drive end instead? The drive-side kit is 3002600340 in the GA 55 / GA 75 group and 3002600370 in the GA 55+ / GA 75+ / GA 90 group. For both ends together the catalogues list the rebearing kits 3002600330 and 3002600360. None of these replaces 3002600350, which is only the non-drive-side kit.
Does the fan kit belong to the 3002600350? No. The motor fan kit is listed separately as 1092026400. It appears alongside 3002600350 in both the fixed-speed and VSD repair lists, but it is an independent part number.
What do the dimensions and weight refer to? The recorded 3002600350 set measures 205 x 205 x 125 mm and weighs 1.3 kg. Those figures describe the supplied kit, not the motor it fits.
Confirming the Match Before You Order
Pass on the number stamped on the removed bearing or ring, and add your compressor model and serial number. Our parts desk will check the 3002600350 against the motor end on your machine and issue a quotation once the match is confirmed, so you receive the correct circlips and seal lip for the job.
المزيد من قائمة الأطقم
| رقم الجزء | اسم الجزء | رقم الجزء |
|---|---|---|
| 1837008940 | BEARING KITS | 1837-0089-40 |
| 1837008941 | BEARING KITS | 1837-0089-41 |
| 1837008942 | BEARING KITS | 1837-0089-42 |
| 2901311610 | BEARING KITC90 A 180L(KBSYNTH) | 2901-3116-10 |
| 2901311810 | BEARING KITC90 A 200L(KBSYNTH) | 2901-3118-10 |
| 1629380126 | CUBICLE FANKIT VSD IEC/UL | 1629-3801-26 |
| 2901364032 | KIT7.5-10HP C43I 6000H/3YR VSD | 2901-3640-32 |
| 2906056900 | GEARBOX OVERHAULKIT | 2906-0569-00 |
| 3002601590 | أطقم 8000 ساعة GA45-75 VSD PM | 3002-6015-90 |
| 3002604760 | 24000H KIT_ ZS90-160(VSD) | 3002-6047-60 |
| 3002604770 | 40000H KIT_ ZS90-160(VSD) | 3002-6047-70 |
| 3002617516 | GEARBOX KIT_G 315-355 | 3002-6175-16 |
| 2903005400 | TOOLKIT FOR FAN REBEARING | 2903-0054-00 |
| 2903005500 | TOOLKIT FOR FAN REBEARING | 2903-0055-00 |
| 2903005600 | TOOLKIT FOR FAN REBEARING | 2903-0056-00 |
| 1092000231 | MOTOR SERVICE KIT FOR GX7-11 | 1092-0002-31 |
| 1092000232 | MOTOR SERVICE KIT FOR GA11-22 | 1092-0002-32 |
| 1092000233 | MOTOR SERVICE KIT FOR GA30C | 1092-0002-33 |
| 1092000234 | MOTOR SERVICE KIT FOR GA30C 23 | 1092-0002-34 |
| 1092000237 | MOTOR SERVICE KIT FOR GA5-7 | 1092-0002-37 |
| 1092000238 | MOTOR SERVICE KIT SCD75K | 1092-0002-38 |
| 1092001243 | MOTOR SERVICE KIT GA15-22 | 1092-0012-43 |
| 1092005058 | MOTOR SERVICE KIT GAE26-30 | 1092-0050-58 |
| 1092005090 | MOTOR OVERHAUL KIT GAE11-22 | 1092-0050-90 |
| 1092005092 | MOTOR OVERHAUL KIT GA26-30 | 1092-0050-92 |
| 1092204001 | GA75VSD+ MOTOR KIT | 1092-2040-01 |
| 1092204002 | GA90VSD+ MOTOR KIT | 1092-2040-02 |
| 1092204003 | GA110VSD+ MOTOR KIT | 1092-2040-03 |
| 1092908211 | MOTOR KIT-LFB15 &50HZ | 1092-9082-11 |
| 1092908326 | MOTOR AND MOTOR ASSEMBLING KIT | 1092-9083-26 |
| 1092908354 | MOTOR AND MOTOR ASSEMBLING KIT | 1092-9083-54 |
| 1092908356 | MOTOR AND MOTOR ASSEMBLING KIT | 1092-9083-56 |
| 1129705364 | F3002/230 AL MOTOR KIT-2FAN | 1129-7053-64 |
| 1129705555 | MOTOR/PULLEY KIT 2.5HP | 1129-7055-55 |
| 1129705562 | MOTOR/PULLEY KIT 3HP | 1129-7055-62 |
| 1129705566 | MOTOR/PULLEY KIT 5.5HP | 1129-7055-66 |
| 1129705572 | MOTOR/PULLEY KIT 7.5HP | 1129-7055-72 |
| 1129705577 | MOTOR/PULLEY KIT 10HP | 1129-7055-77 |
| 1129705582 | MOTOR/PULLEY KIT 15HP | 1129-7055-82 |
| 1129705600 | BEARING KIT PF3 | 1129-7056-00 |
| 1129705622 | BEARING KIT PF7 | 1129-7056-22 |
| 1129705678 | BEARING KIT PS10 | 1129-7056-78 |
| 1129705876 | BEARING KIT PS15 | 1129-7058-76 |
| 1129706045 | BEARING KIT PS7 | 1129-7060-45 |
| 1129706314 | BEARING KIT MS25 | 1129-7063-14 |
| 1129706373 | BEARING KIT | 1129-7063-73 |
| 1129706610 | MOTOR/PULLEY KIT 1.5HP | 1129-7066-10 |
| 1129706619 | BEARING KIT PF1 | 1129-7066-19 |
| 1129706669 | 3HP MOTOR KIT+D120 PULLEY | 1129-7066-69 |
| 1129706704 | MOTOR/PULLEY KIT 2.5HP | 1129-7067-04 |
| الوزن | 1.3 كجم |
|---|---|
| الأبعاد | 20.5 × 20.5 × 12.5 سم |
| اسم الجزء | MOTOR NON DRIVE SIDE KIT FOR OIL INJECTED SCREW COMPRESSORS |
| رقم الجزء | 3002600350 |
| Kit Contents | BALL BEARING x1; EXT.CIRCLIP x1; CIRCLIP-DIN471-75X2.5 x1; SEAL LIP x1 |
| السعر | 680.00 EUR |
| المنشأ | كن |
| رمز التعريفة | 8414909090 |
| الأبعاد | 205 x 205 x 125 mm |
| الوزن | 1.3 kg |
| Side | Non-drive end of the motor |
| التطبيق | GA 55, GA 75, GA 55+, GA 75+, GA 90 fixed speed; GA 55 VSD, GA 75 VSD, GA 90 VSD |































Jaroslav H -
Our GA 55 motor started rumbling at the non-drive end, and the catalogue pointed to kit 3002600350. The carton arrived with a 1.3 kg set in a 205 x 205 x 125 mm box, and all four pieces were there: the ball bearing, two different circlips including the DIN471-75X2.5, and the seal lip. Our technician checked the circlip groove and the seal direction before pressing the bearing home, and the motor ran quiet again. We sent the serial number first and had the fitment confirmed before ordering.